MarineShaft – many tankers don’t realise they can repair shafts

Jul 30 2020


Many tanker operators do not realise that it is possible to fix propeller shafts which have got bent, opting instead for an expensive replacement.

The shaft of a tanker – which connects the propeller to the engine – can get slightly bent if the vessel has a minor knock, such as a propeller hitting an obstruction, or if a bearing fails. This means an urgent repair, because an engine cannot drive a propeller through a bent shaft.


Tanker operators often assume that they need to buy a new shaft, and wait while it is made. A complex repair also means higher stakes in any discussion between parties involved in the accident, so a difficult negotiation.

 

But MarineShaft of Hirthals, North Denmark, has a business doing “cold straightening”- straightening out the existing shaft.

 

Marine Shaft says it has carried out a number of repairs on tankers. They have been repairing shafts for more than 50 years.

 

It can also apply to the shafts which connect steering to rudders, known as rudder stock.

 

“I think it is important for any operator to know the straightening repair possibility – regardless of the type of vessel, because you never know if you might need it,” says Hanne Magnussen, marketing manager of Marine Shaft.

 

Straightening can save time, money, and also achieve environmental benefits.

 

The worst bent shaft the company ever repaired was 1000mm out of line. The vessel had hit a rock off the Norwegian coast, and suffered extensive propeller shaft and rudder damage. The propeller shaft was blocked in turning, and pulled approximately a metre out of the stern tube, becoming heavily bent.

 

Marine Shaft straightened the shaft to 0.02mm out of line – where a new shaft can be up to 0.05mm out of line. “We are talking very narrow numbers here – the thickness of a hair,” she says.

 

The manufacturing of a new propeller shaft can take several months.  But the shaft could be repaired within a couple of weeks.

 

But even slightly bent shafts need to be straightened, otherwise they cause vibration and damage, she says.

 

If there is any vibration, it could turn out to be a huge cost saver to check the shaft alignment.

 

MarineShaft can straighten shafts from 20 mm up to 1,500 mm in diameter, and no limit to in length. They use a hydraulic press, designed and built in house. The maximum press capacity is 8,000 tonnes.

 

The company has propeller shafts and rudder stocks sent from all over the world. Time and price quotations can usually be provided based on photos.

 

In many cases the work can be completed in a few days, much faster than the time to make and deliver a new shaft.

 

The know-how of how to straighten shafts is kept as a company secret. It is not “something you learn by book,” Ms Magnussen says.

 

The process is fully approved by “all major classification societies” and considered as a permanent repair, equivalent to a new shaft. The service includes thoroughly inspecting the shaft for cracks.

 

It does not adversely affect the metallurgy of the shaft material – because the straightening can actually release stress from the material. Although other straightening methods do put stress on the material.

 

The equipment is hydraulic presses with numerical control and sensors.

 

An article published in the in-house magazine for insurance company GARD said that large diameter shafts are often subject to bending, which can occur during manufacturing, processing or in subsequent use.

 



Related News

Army Corps still assessing Louisiana Calcasieu Ship Channel after Delta

(Oct 15 2020)

The U.S. Army Corps of Engineers said it has identified three obstructions from Hurricane Delta that have to be removed before it can reopen the Calcasieu Ship Channel in Louisiana to deep draft vessels.



Hempel launches underwater hull inspections powered by Remote Operated Vehicles (ROVs)

(Oct 07 2020)

Leading global coatings manufacturer Hempel launched an underwater Hull Inspection service using Remote Operated Vehicles (ROVs), to provide complete hull coating inspections while a vessel is at port or anchorage.



Survitec introduces new turn-key service to support shipowner lay-up requirements

(Sep 03 2020)

Survitec has introduced a new service aimed at ensuring CO2 low pressure (LP) firefighting systems are correctly deactivated when ships enter lay-up.



OCIMF extends temporary remote inspection option to Offshore Vessel Inspection Database (OVID)

(Sep 03 2020)

As of 1 September 2020, OCIMF has included a remote vessel inspection option as a temporary tool within its Offshore Vessel Inspection Database (OVID), the inspection protocol for offshore vessels.



Venezuelan floating storage with 173K tons of oil is sinking in Gulf of Paria

(Sep 03 2020)

Floating Storage and Offloading Unit FSO NABARIMA was reported by Eudis Girot, one of the trade unions leaders of Venezuelan Oil Industry, to be in emergency situation, due to lack of proper and professional maintenance.



October 2020

Seafarer morale and safety - Neste and vessel performance - Maersk''s ZeroNorth